New Sensor Features Extended Operating Ranges, Supply Voltages
and Output Configurations to Simplify Control System Compatibility

Honeywell introduces 17 new RPN Series Hall-Effect Rotary Position Sensors that simplify customer use by providing the inputs, outputs and voltage ranges needed for nearly any control system.

Eight operating ranges up to 360° give customers greater control system accuracy by allowing them to select a range more closely suited to their application. Five supply voltage outputs (5 Vdc to 30 Vdc) and eight output configurations (mA or Vdc) improve compatibility with a variety of control systems. Linearity as low as ±0.35° provides customers with increased measurement precision. This precision can be essential depending on the application. Two connector choices (AMP Superseal, Deutsch) satisfy customer connection requirements. The RPN Series’ products also share the same footprint, eliminating special recalibrations and simplifying use.

The RPN Series sensors use solid state Hall-effect technology, providing non-contact operation, enhancing service life and reducing wear-out mechanisms. This Series uses a magnetically based, Hall-effect integrated circuit (IC) to sense rotary movement of the actuator shaft over an operating range. The IC, together with conditioning and protection circuitry and two permanent magnets, is sealed in a rugged package of IP67 or greater for durability in harsh environments. A dual output version is available for redundancy and backup.

This product introduction extends a robust portfolio of position sensors that are found in thousands of vehicles and equipment worldwide. Potential applications include position and movement detection of pedals, throttle, gear shift, levers, linkages suspension and hitches in trucks; off-road vehicles; industrial and construction vehicles and equipment; agricultural vehicles and equipment; and cranes.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

The proven MAH120 handheld scanner is a robust and economical handheld for all standard bar codes and 2D codes. It can read codes from any direction over a distance of 20 to 150mm depending on the symbology. A special version with white LEDs is also now available giving the ability to read both red and green codes.

Confirmation of the code is achieved by means of LED, vibration and acoustic signals. The handheld can be programmed using a simple software program or  by configuration data matrix codes. There is also an additional option of creating customer-specific solutions with a JavaScript editor. Furthermore, the Linux core of the operating system opens up still more options.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

This unique accessory provides a rear of panel seal to Bulgin’s panel mounting waterproof Buccaneer connectors.

The PX0799 backshell replaces the existing panel nut, fixing the connector in place, and provides dust and water protection up to IP68 between the panel and the cable at the rear. This allows a through panel seal with waterproof connections both sides of the panel whilst still retaining a re-wireable capability.

Using the same cable gland sealing system as the standard Buccaneer cable connectors, it will accommodate 6 to 8mm diameter cable as standard, extending from 3.5 to 9.0 with alternative sealing glands.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

New D1D and D2D series solid state relays add to Crydom's
already extensive offer for high-current DC applications
such as heater, lighting and motor control

Crydom's D1D and D2D series of FET output DC Solid State Relays formerly rated up to 40 amps at 100 VDC and 12 amps at 200 VDC, now includes new models rated at 60, 80 and 100 amps at 100 VDC, as well as 40 amps at 200 VDC. The new models which are offered in the industry standard "hockey puck" SSR package, adds to Crydom's present offer which includes the D06 rated to 100 amps at 60 VDC, D2D & D4D series rated to 12 amps and D5D models rated to 10 amps at 200, 400 and 500 VDC respectively.

The new D1D relays feature a low on-state resistance FET output capable of carrying 60, 80 or 100 amps when the SSR is mounted on an appropriately rated heat sink. Likewise, the new D2D40 features a similar FET design rated to 40 amps with appropriate heat sink. Control for these Crydom DC output SSRs is by a transformer isolated 3 to 32 VDC logic compatible input providing 2500 VAC input to output isolation. The outputs are diode protected and specified to operate up to 1 kHz. 

Crydom DC output SSRs are ideal for heating and lighting control as well as motor control in commercial, industrial, medical, aerospace, rail and automotive applications.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Schurter is pleased to announce the added snap-in version of the series 5003 DC power entry module for 48V telecom and other DC-powered equipment. The new DC module features two different standard connector styles, AMP Universal MATE-N-LOK and Molex HCS-125. The connectors are encased with a single stage filter rated up to 15 A at 125 VDC. The filters provide wide-band attenuation in frequencies ranging from 100 kHz to 30 MHz.

Demand for higher data processing and transmission speeds, at the Customer Premises Equipment level, pushes demand upstream to Internet Service Providers and eventually to the core Central Office services. This movement toward higher speed and functionality brings with it the challenge of effectively managing potentially harmful electro-magnetic interferences in equipment used throughout these communications systems. While filtered AC power entry modules have become a popular solution for filtering AC power lines, the concept of a DC filtered power entry module, specifically for telecom equipment, is relatively new.

The 5003 provides optimal shielding at the panel opening. It includes a screw mount version for front or rear mounting to the chassis as well as the new snap-in version. The version for rear mounting allows for pre-wiring of the module prior to installation. Labor cost saving options can be realized by using either the snap-in version or the rear mount version with its pre-threaded holes. 

The non potted design provides maximum performance in a lightweight and environmentally friendly compact package. The series is ENEC and cURs approved and complies with IEC/EN 60950 standard, for office and IT equipment. Applications include network routers, LAN switches, WAN switches and multiplexers, as well as other equipment using DC power supplies.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

The 2009 edition of ABB’s drives and motors catalogue is now available for end-users, system integrators and Original Equipment Manufacturers (OEMs). The 48 page catalogue is free and can be downloaded directly from www.abb.co.uk/energy or a hard copy is available from freephone Brochureline on 0800 783 7491.

The catalogue provides technical details of ABB’s range of low voltage AC drives from 0.18 to 2,800 kW and motors from 0.06 to 710 kW. It also presents ABB’s range of DC and medium voltage AC drives. Easy-to-use tables give ordering data, dimensions, options and electrical details for most products, together with prices for 2009.

New products for this year include an IP66 rated ABB general machinery drive. From 0.37 to 7.5kW the drive is suitable for screws, mixers, pumps, fans and conveyors in places where the machinery is exposed to dust, moisture and high pressure washing such as the food and drinks sector. The ABB standard drive range and the ABB industrial drive range have also seen their power range boosted and are now available up to 160kW.

Supporting software includes integration and programming tools, start-up and maintenance tools, as well as engineering and energy saving tools. Web links tell readers where to download the different packages.

As well as product details, the 2009 brochure outlines the services available to support drives customers. DrivesActive, provides 24/7 support, while DrivesActive+ is a lifecycle management programme for critical equipment. DrivesAdvantage completes the service portfolio with installation, start-up and after-sales support.

The catalogue also includes details of the ABB Drives Alliance and Motor Service Partners located throughout the UK. The partners stock a wide range of ABB drives and motors, many available off-the-shelf or available for delivery at short notice.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

AS-Interface Gateway / Safety Monitor

This device combines an AS-Interface Gateway with a Safety Monitor in a single integrated housing. It can monitor the assigned AS-Interface sensors with the latest configuration software. This monitor has a stainless steel housing with LCD display for indication of slave addresses and error messages. The configuration data is stored in the internal EEPROM and can be overwritten by data stored on a memory card or vice versa. The AS-Interface Safety Monitor enables the use of sensor-controlled safety components according to EN954-1 up to category 4/SIL 3.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Dust and Waterproof to IP 67

*  Two Materials, Polycarbonate - UL 94 V0 Rated or ABS - UL94-HB Rated
*  Threaded knockouts, premoulded areas that can be pushed out for use with M20 size cable glands
*  Plastic lid fixing screws, corrosion resistant
*  Captive lid screws, standard on all lids
*  Available with optional 22mm holes, suitable for standard switches and indicators
*  PCB mounting, mounting posts and slots for PCB as standard
*  Self tapping screw fixing, standard feature
*  Transparent top cover, available in clear and smoke grey

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Schurter’s new power entry modules, series DD11 and DD12, are designed to be extremely compact and robust. The DD11 is equipped with multiple functions including an IEC C14 appliance connector, switch and fuseholder. The DD12 combines the same functions and additionally includes a line filter.

The compact design makes the series ideally suited for the use in equipment with limited space and more demanding electrical and mechanical requirements. Their excellent performance ensure their potential applications are wide-ranging, they are suitable for almost any application requiring detachable power, including medical, office, household appliances and automation. When mounted perpendicular to the board, the modules fit within one rack unit (1RU) enclosures, also making them particularly ideal for IT and telecom applications.

The series mounts to the panel with screws. The filtered version has a broad metal flange, ensuring optimal contact to the appliance chassis for ideal shielding and filtering. Special filters with enhanced voltage withstand are available on request. The series is ENEC and cURus approved and complies with IEC/EN standards for office and medical equipment, 60950 and 60601-1 respectively.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/